|
|
DT Receiver - Rx100-T-v502 - Programming
|
1. PROGRAMMING APPROACH:
|
|
|
1. Switch Transmitter on.
2. Hold left/right sticks (Ch2/4) in towards middle of Tx.
3. Switch Receiver on and wait for the Led to flicker very fast.
4. Center all sticks.
5. The led flashes the setting for the first 'Level' (eg: 1-flash = H outputs).
6. Yes = push the Ch3 (Elevator) stick forward (to top of Tx) to accept this and advance to next Level.
7. No = pull the Ch3 (Elevator) stick back (to bottom of Tx) to see next option for same Level.
8. Continue through all Levels until Led comes on solid.
9. Settings are saved automatically at the end so switch off at any time to abort.
10. Say 'yes' to every item to just see what is currently set.
|
Changing 'P2' from Ch4 to Ch5. Level 1: 3-flash = P Level 2: 2-flash = P2 Level 3: 1-flash = Servo Level 4: 5-flash = Ch5 |
2. PROGRAMMING OPTIONS:
|
Level 1 'H', 'F', 'P' or 'Other' |
Level 2 Output number |
Level 3 Output type |
Level 4 Channel number |
Level 5 Other choices |
Default | Information |
| 1 flash = 'H' outputs | Not used | |||||
|
|
||||||
| 2 flash = 'F' outputs | Not used | |||||
|
|
||||||
| 3 flash = 'P' outputs | 1-8 flash = P1-8 | 1 flash = Servo | 1-7 flash = Channel 1-7 | 1-8 servos no mix | ||
|
|
||||||
| 3 flash = 'P' outputs | 1 flash = P1 |
2 flash = Servo 2 channel mix |
1-7 flash = 1st Ch 1-7 |
1 flash = 0% mix 2 flash = 12.5% mix 3 flash = 25% mix 4 flash = 50% mix 5 flash = 100% mix | 31225 | P1/P2 used as a pair |
| 3 flash = 'P' outputs | 2 flash = P2 |
2 flash = Servo 2 channel mix |
1-7 flash = 2nd Ch 1-7 |
1 flash = not reversed 2 flash = reversed |
32231 | P1/P2 used as a pair |
|
|
||||||
| 3 flash = 'P' outputs | 1-8 flash = P1-8 | 3 flash = Brake or Reverse led |
1-7 flash = Activating Ch |
1 flash = Brake 2 flash = Reverse |
33331 35332 |
1 channel controls 2 outputs |
|
|
||||||
| 3 flash = 'P' outputs | 1-8 flash = P1-8 |
4 flash = Left indicator led 5 flash = Right indicator led 6 flash = Flashing led (0.5s) |
1-7 flash = Activating Ch | 1-7 flash = Steering Ch 1-7 |
34442 37542 3664 |
1 'activating' channel controls 3 outputs 1 'steering' channel cancels left/right Steer channel picks up 'trim' on startup Activ. stick left/right <1s = L/R on/off Activ. stick left >2s = Hazards on/off Activ. stick right >2s = Flasher on/off |
|
|
||||||
| 3 flash = 'P' outputs | 1-8 flash = P1-8 | 7 flash = On/Off led | 1-7 flash = Channel 1-7 |
1 flash = 'high' stick >2s on/off 2 flash = 'high' stick <1s on/off 3 flash = 'low' stick >2s on/off 4 flash = 'low' stick <1s on/off |
1 channel controls 1-4 outputs Outputs 'toggle' on/off |
|
|
|
||||||
| 3 flash = 'P' outputs | 1-8 flash = P1-8 | 8 flash = On/Off led | 1-7 flash = Channel 1-7 |
1 flash = 'low' stick on 2 flash = 'high' stick on |
38812 |
1 channel controls 1-2 outputs Up to 4 leds using 2-4 channels 'Center' = off |
|
|
||||||
| 4 flash = Other settings | 1 flash = 'Other 1' |
1 flash = Arming: Disabled 2 flash = Arming: Low stick 3 flash = Arming: Middle stick |
1-7 flash = Arming Ch 1-7 |
1 flash = LVC Disabled 2 flash = LVC Enabled |
41332 | |
|
|
||||||
| 4 flash = Other settings | 2 flash = 'Other 2' |
1 flash = LED2 Disabled 2 flash = LED2 Enabled |
1-8 flash = LED2 Pad P1-8 |
1 flash = No reset 2 flash = FACTORY RESET |
42241 |
LED2: use a Pad number that is driving any Led LED2: 'disable' if all outputs are servos Factory Reset = Restore Defaults |
|
|
3. DX3:
1. Use full 'brake' to make receiver enter programming mode on startup.
2. Use 3-position Aux channel to make yes/no choices.