|
|
DT Receiver - Rx43d-1-v502 - Instructions
|
|
1. DEFAULT SETUP
- Car with 1 Motor (reversable), Steering (servo or 2-actuator or 2-muscle wire) and 7-8 Lights.
- Train with 1 Motor (reversable) and 2-5 Lights.
- Plane requires changes.
- All outputs can be customised / re-configured.
| Output | Type | Channel | Other |
| H1: | Motor 'half stick' control (center off) | Ch3 | |
| F1: | 2-coil actuator / muscle wire / ADD1 | Ch2 steering | Left stick gives Switch action (eg: light) |
| F2: | 2-coil actuator / muscle wire / ADD1 | Ch2 steering | Right stick gives Switch action (eg: light) |
| P1: | Servo | Ch2 Steering | |
| P2: | Left indicator Led | Ch4 left <1s on | Ch2 steering/auto cancel |
| P3: | Right indicator Led | Ch4 right <1s on | Ch2 steering/auto cancel |
| (P2/P3): | Hazards (Left+Right) | Ch4 left >2s toggle on/off | |
| P4: | Flashing Led (0.5s) | Ch4 right >2s toggle on/off | |
| P5: | Driving lights Leds (Front & Rear) | Ch1 up >2s toggle on/off | |
| P6: | Led | Ch1 down >2s toggle on/off | |
| P7: | Brake Led | Ch3 auto activate | |
| P8: | Reverse Led | Ch3 auto activate | |
| Arming/Activation: | Mid-stick to enable | Ch3 | |
| LVC |
Mid-stick to acknowledge Brake light ON; outputs OFF 'LED2' 2-flash |
Ch3 | |
| LED2 | External LED to show receiver activity | P5 (driving lights) |
2. EXAMPLE CONNECTIONS:
|
|
for extra H output |
|
|
|
|
LEDs with 1S Lipo:
Led's driven from P outputs only require a current limiting resistor (8mA max).
Led's driven from F outputs only require a current limiting resistor (2A max).
LEDs with 5-6v:
'P' outputs are 3v when 'off' and 0v when 'on'. So when used with higher voltages, the leds driven from P outputs also need diodes to reduce the voltage. This is because 5 or 6v is high enough above the 3v output to make Leds conduct even when P outputs are 'off'. An example is shown in the Led (P1) diagram.
Led's driven from F outputs only require a current limiting resistor when operated off any voltage up to 6v.
GRAIN of WHEAT:
Grain of Wheat bulbs usually draw >8mA so are not suitable for use with P outputs (unless buffered with a transistor).
Grain of Wheat bulbs can be driven from F outputs. F outputs allow the intensity to be varied with stick movement or 'Travel Adjust'.
3. CHANGING OUTPUTS:
All outputs can be customised / re-configured:
PROGRAMMING
4. GENERAL:
The Rx is not insulated.
The PCB is thin so do not bend it.
5. LED:
Led On = perfect reception (real-time indicator).
1 flash = Scanning (~2sec between flashes; wrong model if never stops).
2 flash = Brownout (receiver voltage went too low; check battery/servo load).
6. FAILSAFE:
Outputs are not driven (do nothing) on startup and while scanning.
Outputs 'hold' on short signal losses (<1sec) and then do nothing (>1s).
7. BINDING:
1. Switch Rx on and wait ~20s until led flickers fast.
2. Switch Tx on in bind mode and Rx led should flash slowly and then go solid.
3. Change distance between Tx/Rx if binding does not work.