|
|
Rx65 Overview
|
|
|
|
|
|
|
|
|
PCB ID: 65a Not latest version
PRODUCT: Rx65
INSTRUCTIONS: Rx65-1 | Rx65-2 | Rx65-22 | Rx65-3 | Rx65-4 | Rx65-5 | Rx65-6
PROGRAMMING: v610
ALL FEATURES
DESCRIPTION:
Receiver for surface vehices.
All variants are physically identical and have the same software but different defaults.
All outputs can be changed individually by operator.
|
Variant |
Rx65-1 |
Rx65-2 Rx65-22 |
Rx65-3 |
Rx65-4 Rx65-5 |
Rx65-6 | Details |
|
Purpose: |
Train with joystick Tx |
Train with Tx20 Tx21 Tx22 |
Conven- tional |
Car with joystick Tx or Dx3* |
Boat with joystick Tx |
* Rx65-5 for Dx3 |
|
'H' output: (H-Bridge) |
1 |
1 |
1 |
1 |
1 |
Integrated forward/reverse ESC for brushed motors 512 step PWM control |
|
Motor control |
'Low off' | 'Center off' | 'Center off' | 'Center off' | 'Center off' | |
|
Direction channel |
Yes |
- |
- |
- |
- |
|
|
'P' outputs: (Pads) |
4 |
4 |
4 |
4 |
4 |
Signal pads for Servos and low current on/off switching Special programs for car lights and other switching 1024 step Servos Serial data feed |
| 2A buffered output | 1 | 1 | 1 | 1 | 1 |
All 4 P outputs can drive 20mA loads (eg: leds) Output 'P1' controls Pad 'A' which can drive a 2A load |
|
BEC: |
Yes | Yes | Yes | Yes | Yes |
A 3.3v 500mA 'battery elminator circuit' output is available alongside P4 |
|
'L' pad: |
Yes | Yes | Yes | Yes | Yes |
Lipo booster monitor Low voltage protection for a single cell lipo when used with a voltage booster |
|
'Selecta':
|
- |
Enabled (Rx65-22) |
- | - | - |
Selecta can activate and deactivate models without touching them (Available on all variants but enabled on Rx65-22 only) |
| Size: | 13.4 x 31.2mm (0.6x1.3") 'N' and 'W' versions are 5mm thick, 'C' and 'U' versions are 7.5mm |
|||||
| Weight: | 1.7g ('N' version) | |||||
| Pad spacing: | 2.54mm (0.1") |
|||||
| Voltage range: | 2.9-18v (20v 'absolute max', operates down to 2.6v) | |||||
| Motor current |
3A with 16kHz PWM (motor stalled at 100% throttle) |
|||||
| Rx current: | 16mA | |||||
| Rx outputs: | 5 (see above) | |||||
| Tx channels*: | 14 max (9 tested) | |||||
| Modulation: | 2.4GHz compatible with 22ms DSM2 and DSMX Air and 16.5ms DSM2 Surface |
|||||
| Range: | Indoor/Outdoor |
* = Channels that can be used to control receiver outputs (all outputs can be associated with any channel)
HARDWARE OPTIONS:
The 'N' version has no wires or connectors (bare board).
The 'W' option is 2 wires for power, 2 wires for the motor and heatshrink covering.
The 'Z' option is a 1.5mm pitch JST ZH socket (with correct pin polarities +-s).
The 'P' option is a 1.25mm pitch Molex PicoBlade socket (servo wires must be swopped).
The 'T' option is a 2.54mm (0.1") pitch Turned-Pin socket for P1, P2, P3 and the A output.
The 'U' option is a 150mm coax aerial with U.FL socket (the U.FL socket allows the arerial to be replaced).
INSTRUCTIONS:
| Rx65-1 | Rx65-2 | Rx65-22 | Rx65-3 | Rx65-4 | Rx65-5 | Rx65-6 | Change from previous version | Version |
v610 |
v610 |
v610 |
v610 |
v610 |
v610 |
v610 |
Toggle servo, Adjustable LVC, Prog3, Variant change (changes relative to v603) |
PROGRAMMING:
| Programming table | Feature descriptions | Version |
v610 |
v610 |