|
DelTang has ceased trading. Thank you for your support. This web site is retained for reference only, instructions for all products are below. Contact Micron R/C to enquire about replacements for Deltang receivers.
INSTRUCTIONS
Click to enlarge |
Name | GBP | Weight | Size | Connector/Pad spacing | DSM |
Brushed ESC (planes) |
SumPPM Serial options |
Channels | Comment |
Rx31 Rx31-K1 Rx31-Sum |
- - - |
0.21g 0.21g 0.21g |
9.3 x 9.9mm |
1.27mm (0.05") | DSM2 | - |
Y Y Y |
5 7 7 |
Rx31 has 5 servo outputs Rx31-K1 has 7ch Serial output Rx31-Sum has 7ch SumPPM/CPPM Product page | Instructions (v3.4) |
|
Rx31-F |
- | 0.23g |
9.3 x 9.9mm |
1.27mm (0.05") | DSM2 | 1 | Y | 5 |
Product page | Instructions (v3.4) Physically the same as above but has FET installed for motor ESC | |
Rx31d-F | - | 0.23g |
9.8 x 10.2mm |
1.27mm (0.05") | DSM2 | 2 | Y | 4 |
Product page | Instructions (v3.4.4) Twin-steer |
|
Rx32d | - | 0.28g |
11.1 x 12.0mm |
1.27mm (0.05") | DSM2 | - | Y | 7 |
Product page | Instructions v3.4 Serial/SumPPM options |
|
Rx33 | - | 0.65g |
13.3 x 15.7mm |
1.0mm JST SH (IDC) -Spektrum & Falcon servos |
DSM2 | 1 | Y |
6 4 plugs |
Instructions (v3.3) Instructions (v3.4) |
|
Rx34d | - | 0.68g |
11.7 x 16.5mm |
1.25mm MOLEX PICOBLADE -Futaba/Walkera/HobbyKing |
DSM2 | 2 | Y |
6 4 plugs |
Product page | Instructions (v3.4) Twin-steer |
|
Rx35d-N Rx35d-V Rx35d-V-7 |
- - - |
0.35g 0.71g 0.71g |
12.1 x 17.0mm |
1.5mm JST ZH -as used on Spektrum AR6300 |
DSM2 |
2 2 - |
Y Y Y |
5(7) 5(7) 7 |
5 servo pads, 2 ESC's 4 servo sockets, 1 servo pad, 2 ESC's 4 servo sockets, 3 servo pads Instructions (v3.4) |
|
Rx36-N Rx36-H |
- - |
0.38g 1.30g |
11.6 x 26.3mm |
2.54mm Standard -Horizontal or No connectors |
DSM2 | 1 | Y |
6 4 plugs |
Instructions (v3.3) Instructions (v3.4) |
|
Rx27-N Rx27-H |
- - |
0.7g 2.1g |
14.5 x 29.0mm |
2.54mm Standard -Horizontal or No connectors |
DSM2 | Y | Y |
6 5 plugs |
Instructions (v2.6) More range than Rx36 (> Parkfly) |
|
Rx37 Rx37-F |
- - |
0.31g 0.33g |
14.1 x 15.0mm |
Solder points on Rx for servo +/- Designed for F3P | DSM2 |
- 2 |
Y Y |
7 7 |
Product page | Instructions (v3.4.4) |
INSTRUCTIONS
Click to enlarge |
Name | GBP | Weight | Size | Pad spacing | DSM |
Actuator outputs |
Brushed ESC (planes) |
Servo outputs |
Comment |
Rx41d | - | 0.28g |
10.1 x 10.8mm |
1.27mm (0.05") | DSM2 | 1 | 2 | 3 |
Product page | Instructions (v3.4.4) Twin-steer |
|
Rx43d | - | 0.35g |
11.8 x 12.9mm |
1.27mm (0.05") | DSM2 | 3 | 2 | 4 |
Product page | Instructions (v3.4.4) Twin-steer |
INSTRUCTIONS
Click to enlarge |
Name | GBP | Size | DSM |
2-way motor current ('H') |
H outputs (motor) |
F outputs (buffered) |
P outputs (on/off) |
Info |
|
Rx41d-1 Rx41d-2 Rx41d-3 Rx41d-22 |
- |
10.1 x 10.8mm |
DSM2+ DSMX |
500mA | 1 | 2 | 3 |
Instructions: v510 | v520 Instructions: v510 | v520 Instructions: v510 | v520 Instructions: v510 | v520 Product page |
Rx43d-1 Rx43d-2 Rx43d-3 Rx43d-32 Rx43d-4 Rx43d-6 |
- - - - - - |
11.8 x 12.9mm |
DSM2+ DSMX |
400mA 400mA 400/800mA 400/800mA 400/800mA 400mA |
1 2 3 3 4 1 |
2 2 2 2 2 2 |
8 6 4 4 2 8 |
Instructions: v510 | v520 Instructions: v510 | v520 Instructions: v510 | v520 Instructions: v510 | v520 Instructions: v510 | v520 Instructions: v520 Product page |
|
Rx45-v5 (Car) Rx45-22 (Train) Rx45-6 (Car) |
- |
9 x 9.6mm |
DSM2+ DSMX |
500mA | 1 | 2 | 6 |
Instructions: v510a | v510b | v520 Instructions: v510a | v510b | v520 Instructions: v520 Rx45b Current PCB Rx45a Previous PCB |
|
Rx47-x |
- |
10 x 17.3mm |
DSM2+ DSMX |
800mA | 2 | 2 | 14 |
Rx47-4 = Car version Rx47-6 = Car version (#2) Rx47-22 = Train version All variants: 1 | 2 | 22 | 3 | 4 | 6 |
|
ADD1 ADD2 |
- - |
4.4 x 9.0mm 6.3 x 12.5mm |
. |
800mA 3000mA |
1 1 |
Addon boards boost power of H outputs and convert F outputs to H outputs Product page |
|||
Prog4 Prog3 Prog2 |
- - - |
18 x 40mm |
. | . | . | . | . |
Programming options |
INSTRUCTIONS
Click to enlarge |
Name | GBP | Size |
Motor (H) Amps | Volts (3v min) |
H outputs (motor) |
P outputs (on/off) |
F outputs (buffered) |
Info |
|
Rx66 |
- |
26x46mm (1.1x1.8") |
4A base 6A heasink 3-18v |
1 | 8 | 3 |
Rx66a Current version |
|
Rx65 |
- |
14x38mm (0.6x1.5") |
3A 3-13v |
1 | 8 | 3 |
Rx65c Current version Rx65b Previous version Rx65a Previous version |
|
Rx62 |
- |
12.4 x 24.6mm (0.5x1.0") |
1.3A 3-13v |
1 | 4 | - |
Rx62b Current version Rx62a Previous version Integrated electronic switch (reed) |
|
Rx61 |
- |
12x22.5mm (0.5x0.9") |
1.3A 3-13v |
1 | 8 | - |
Rx61d Current version Rx61c Previous version Rx61b Previous version |
|
Rx60 |
- |
11x22.5mm (0.4x0.9") |
1.3A 3-13v |
1 | 5 | - |
Rx60c Current version Rx60b Previous version |
|
Rx63 |
- |
9.6 x 16.6mm (0.4x0.65") |
1.0A | 4.2v 0.5A | 8.4v |
1 | 4 | . |
x = 1, 2, 22, 3, Compare |
. | . | . | . | . | . | . | . | . |
|
Rx102-x Rx102-x-U |
- - |
18 x 40mm U=Coax aerial |
. | 8 | . |
Receiver with directional lights for trains Adjustable servo throws for live steam Heatshrink covered Instructions |
|
Prog4 Prog3 Prog2 Prog1 |
- - - - |
18 x 40mm |
. | . | . | . |
Programming options |
INSTRUCTIONS
Click to enlarge |
Name | GBP | Size | Description |
Tx20-Kit Tx20-Built |
30x54x82mm (box size) |
1 train controller. One Speed control, three push-button controls and one self-centering 3-way switch. Often used with Rx41d-2-v5 (1 lipo) or Rx6x-2 (1-4 lipos) or Rx102. |
||
Tx21-Kit Tx21-Built |
30x54x82mm (box size) |
1 train controller. One Speed control, Inertia, one push-button and one 2-way switch. Often used with Rx41d-2-v5 (1 lipo) or Rx6x-2 (1-4 lipos) or Rx102. |
||
. | . | . | . | . |
Tx22-Kit Tx22-Built |
24x58x113mm (box size) |
12 train controller (if used with receivers with 'Selecta'). One Speed control, Inertia, Selecta, one push-button and one 3-way switch. Often used with Rx41d-22-v5 (1 lipo), Rx6x-22 (1-4 lipos) or Rx102. |
||
Tx24-Kit Tx24-Built |
24x58x113mm (box size) |
12 model controller (if used with receivers with 'Selecta'). Same as Tx22 but Direction switch changed to a knob (pot). This allows it to 'steer' (eg: cars/boats) as well as operate trains. The Inertia pot can be made to control a channel so the Speed, Direction and Inertia knobs can control up to 3 channels in a proportional manner (eg: for live steam). |
||
Tx72-Kit Tx72-Built |
24x58x113mm (box size) |
12 train controller (if used with receivers with 'Selecta'). Same as Tx22 but with Menu control (with suitable receivers). |
||
. | . | . | . | . |
Tx23-Kit Tx23-Built |
31x63x114mm (box size) |
3-train controller. Three Speed controls, Inertia, one push-button and three 2-way switches. Often used with Rx41d-2-v5 (1 lipo) or Rx6x-2 (1-4 lipos) or Rx102. |
||
. | . | . | . | . |
Tx2 |
- |
18 x 40mm |
Tx2 is a self-contained module used to make useful transmitters (eg: see above). It can control up to 7 channels with Trims, Reversing, Throws, Mixing and Inertia. It is a short-range transmitter that works with all DSM2 receivers. Product page | Instructions (v207) |
|
CB2 |
- |
18 x 40mm |
CB2 is an upgrade for Tx2. It is used to control an external transmitter module (not supplied). It is usually used to make a longer range transmitter. Product page |
|
. | . | . | . | . |
Tx1-M | - | 18 x 40mm |
Tx1-M is a 'module' to convert traditional transmitters to DSM2. It requires a PPM input from a trainer plug and some components to control voltages (not supplied). It controls up to 7 channels. It is a short-range transmitter that works with all DSM2 receivers. Product page | Instructions |
|
Tx1-K1 | - | 18 x 40mm |
Tx1-K1 accepts a 16 byte RS-232 data feed on one pin. 7 channels are transmitted. It is a short-range transmitter that works with all DSM2 receivers. Instructions |
|
Tx1-J | - | 18 x 40mm |
Tx1-J is a stand-alone 2-channel transmitter. It has a 5-way push-button navigation 'joystick' similar to that used on cell phones. It is a short-range transmitter that works with all DSM2 receivers. It only needs a battery to make it work. Product page | Instructions |
INSTRUCTIONS
Click to enlarge |
Name | GBP | Size | Description |
Tx27-Kit Tx27-Built |
. |
30x54x82mm (box size) |
Transmitter: Seven 2-way switches for points, semaphores and lights. Intended for use with Rx105 |
|
Tx3-H Tx3-V |
- |
18 x 40mm |
Transmitter module: Remote control of complex layouts with up to 45 functions. It can only be used with Rx105. H=Horizontal pins, V=Vertical pins |
|
Rx105-x |
- |
18 x 40mm |
Receiver for layouts (eg: lights, points, signals) Intended for use with Tx3 and Tx27. |
MORE RECEIVER INFO:
Detailed specifications
Older designs